Energy Saving Products for HVAC

Energy saving products are popping out of the woodwork. Do they work? I do not promote anything unless i know it works.

The ceramic coating listed below, I have personally tested, and it works

A/C Protective Ceramic Coating

The first coating to improve heat transfer and air flow
Reduces hydrocarbon and other airborne contaminate build-up
Minimizes salt build-up on coastal installations
Low cost
Easy to apply
Typical ROI is less than 6 months

---

---

Below are the results of using Ceramic coatings on HVAC.  Savings of $5200 Dollars

Energy Saving products and HVAC

---

How does SIMIX A/C Protective fit in the energy saving products? SIMIX is nano-engineered, and works in the world of particles that are one thousand times smaller than the human eye can see. SIMIX contains sub-nano and nano-particles which bind together in a tight structure. The coating is applied to the condensing coil fins and as it’s sprayed on, it wicks into the microscopic voids between the fin and tube connection. It fills the voids that are created between the fin and tube connection during the first 90 days of operation. It immediately improves heat transfer between the tube and the fin. Simix energy saving products improves air flow by breaking surface tension. More air can move through the opening because there is no friction on the fins. The more CFM pulled through a unit, the more efficient the unit becomes. In most cases, the unit is restored back to its original specifications.

How do I apply SIMIX Energy Saving products? It’s simple. Pull the unit’s breaker. Apply SIMIX All Purpose Cleaner with a misting sprayer. Allow to sit for a couple minutes. Then thoroughly rinse with water. Replace the unit’s breaker and turn on to dry for approximately ten minutes. Pull the unit’s breaker again, and then use a high pressure/low volume sprayer to evenly apply the product over the coils, fins, fans and cabinet. Spray both sides of coils, fins, fans and cabinet. Spraying the cabinet and supports will extend their life. Replace the unit’s breaker and run unit for 30 minutes to cure the coating. You can watch a YouTube video in which we demonstrate the process here.

Bent fins cost you money. How does SIMIX help you restore them? Repair the bent fins by misting a small amount of SIMIX A/C Protective Coating above, on and below the damaged area using a trigger spray bottle. Insert the appropriate sized fin comb under the damaged area and pull upwards through the damaged area; repeat starting from the top and pulling back down through the same damaged area. This technique cuts the normal repair time by over 90%.

How long does SIMIX A/C Energy Savings Products last? Depending on your environment, it will last five to seven years. Corrosive environments may require re-application sooner.

How does SIMIX A/C Energy Savings products improve energy efficiency? Over time, aluminum begins to erode and forma layer of oxidation that becomes an insulator, which in turn slows down the process of dissipating the heat. SIMIX A/C Protective Coating penetrates this layer of oxidation and converts it from an insulator to a conductor, thus restoring efficiency. SIMIX A/C Protective Coating contains nano particles of titanium dioxide, which break down surface tension on fins, resulting in an immediate increase of air movement across the surface. The faster you can get the aluminum fins to dissipate heat, the quicker the fins pull heat from the copper tubing.

What kind of savings can I expect? On a new unit, we recommend applying the product after 90 days of operation. You can expect a savings of at least 3% the first year. Existing installations have shown savings of 15% or more. Cleaner units require less maintenance.

How long does it take for Simix Energy Saving Products to work? The unit’s efficiency decreases temporarily as the coating dries, then will increase within hours and will continue to improve over the next week as SIMIX A/C Protective Coating fully cures.

How does SIMIX A/C Protective Coating make it easier to clean the unit? First of all, units just stay cleaner once coated with SIMIX. That’s because the coating breaks down the exhaust gas emissions and significantly limits the ability of dirt and debris from attaching. A/C units in climates that get a lot of rain will be kept clean by moisture pulled into the fins by the fan. In drier climates, rinsing with a garden hose periodically will keep the fins clean. In areas with excessive airborne pollution, a small amount of diluted SIMIX All Purpose Cleaner followed by rinsing with a garden hose will be all you need to assure the unit is operating at maximum efficiency. (Using any other type of cleaner may result in the destruction of Simix A/C Protective Coating.)

How much does the product cost per ton? Less than $10.

Who could install SIMIX A/C Protective Coating? A qualified maintenance person, painting contractor or your A/C service provider. .

What makes SIMIX A/C energy saving products environmentally friendly? The nano particles of titanium dioxide imbedded in SIMIX A/C Protective Coating react to UV rays from the sun to photocatalytically breakdown hydrocarbons in the air. Hydrocarbons are created by exhaust emissions from cars, trucks and airplanes. Basically, SIMIX helps break down air pollution.c

Return from Energy Saving Products to building maintenance